Hier sind einige Linux-Berichte:
smartctl 6.0 2012-10-10 r3643 [i686-linux-3.5.6-pmagic] (local build)
Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: FUJITSU MHZ2400BT G1
Serial Number: K70BT8A26WYY
LU WWN Device Id: 5 00000e 042d71c8f
Firmware Version: 0041000C
User Capacity: 400,088,457,216 bytes [400 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 3f
SATA Version is: SATA 2.5, 1.5 Gb/s
Local Time is: Mon Jun 20 20:38:21 2016 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 2208) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 254) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 10922
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 109576192
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 5655
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 0 (2000 0)
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 3240
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 6620
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 4088
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 263
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 36439
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 36 (Min/Max 8/46)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 (0 6966)
197 Current_Pending_Sector 0x0012 100 099 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 099 099 000 Old_age Offline - 3
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 18108
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 3728033905769
240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 492 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 492 occurred at disk power-on lifetime: 6619 hours (275 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 8b 3a 7d ec 40 Error: WP at LBA = 0x00ec7d3a = 15498554
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 01 10 d8 1c 79 40 00 00:38:57.160 WRITE FPDMA QUEUED
61 00 08 c0 8a ec 40 00 00:38:57.154 WRITE FPDMA QUEUED
61 00 00 c0 89 ec 40 00 00:38:57.154 WRITE FPDMA QUEUED
61 00 f8 c0 88 ec 40 00 00:38:57.154 WRITE FPDMA QUEUED
61 00 f0 c0 87 ec 40 00 00:38:57.154 WRITE FPDMA QUEUED
Error 491 occurred at disk power-on lifetime: 6619 hours (275 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 83 9b 7c 2d 40 Error: UNC at LBA = 0x002d7c9b = 2981019
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 80 20 7c 2d 40 00 00:38:50.809 READ FPDMA QUEUED
2f 00 01 10 00 00 40 00 00:38:50.668 READ LOG EXT
61 00 78 50 6f ec 40 00 00:38:44.296 WRITE FPDMA QUEUED
61 00 70 50 6e ec 40 00 00:38:44.296 WRITE FPDMA QUEUED
61 00 68 50 6d ec 40 00 00:38:44.296 WRITE FPDMA QUEUED
Error 490 occurred at disk power-on lifetime: 6619 hours (275 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 0b ca 71 ec 40 Error: WP at LBA = 0x00ec71ca = 15495626
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 78 50 6f ec 40 00 00:38:44.296 WRITE FPDMA QUEUED
61 00 70 50 6e ec 40 00 00:38:44.296 WRITE FPDMA QUEUED
61 00 68 50 6d ec 40 00 00:38:44.296 WRITE FPDMA QUEUED
61 00 60 50 6c ec 40 00 00:38:44.296 WRITE FPDMA QUEUED
61 00 58 50 6b ec 40 00 00:38:44.296 WRITE FPDMA QUEUED
Error 489 occurred at disk power-on lifetime: 6619 hours (275 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 3b 99 7c 2d 40 Error: UNC at LBA = 0x002d7c99 = 2981017
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 48 20 7c 2d 40 00 00:33:40.890 READ FPDMA QUEUED
60 00 40 20 7b 2d 40 00 00:33:40.890 READ FPDMA QUEUED
60 00 38 20 7a 2d 40 00 00:33:40.890 READ FPDMA QUEUED
61 08 30 38 0b cc 40 00 00:33:40.890 WRITE FPDMA QUEUED
61 08 28 00 53 c9 40 00 00:33:40.889 WRITE FPDMA QUEUED
Error 488 occurred at disk power-on lifetime: 6619 hours (275 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 0b b7 f5 ed 40 Error: UNC at LBA = 0x00edf5b7 = 15594935
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 c8 18 78 ef 40 00 01:05:23.909 READ FPDMA QUEUED
60 08 c0 c8 37 f2 40 00 01:05:23.874 READ FPDMA QUEUED
60 80 b8 c0 ca ef 40 00 01:05:23.848 READ FPDMA QUEUED
61 00 b0 f0 51 ea 40 00 01:05:23.816 WRITE FPDMA QUEUED
61 00 a8 f0 50 ea 40 00 01:05:23.816 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 6620 590183579
# 2 Short offline Completed: read failure 90% 6619 590183579
# 3 Conveyance offline Completed: read failure 90% 6619 590183579
# 4 Conveyance offline Completed: read failure 90% 6585 590183579
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Ich habe eine Festplatte. Ich habe versucht, sie zu defragmentieren, und beim ersten Mal fror der Cursor von Windows 7 ein und alles andere wurde schwarz, und beim zweiten Mal erschien ein blauer Bildschirm (ich weiß nicht, was der Code war). Es gibt im Grunde keine weiteren Informationen.
Antwort1
Sie haben wahrscheinlich fehlerhafte Sektoren auf Ihrer Festplatte.
Von einer administrativen Eingabeaufforderung aus: chkdsk /R c:
SagenJaum dies beim nächsten Neustart zu tun. Warten Sie, bis Sie Stunden Zeit haben, starten Sie neu und lassen Sie den Test laufen. Vielleicht kurz bevor Sie ins Bett gehen.