☰

Barracuda 7200.12 macht ein sehr lautes Geräusch (Quietschen). Laufwerk wird nicht angezeigt

tag-icon • tag-icon hard-drive hard-drive-failure
Barracuda 7200.12 macht ein sehr lautes Geräusch (Quietschen). Laufwerk wird nicht angezeigt

Ich habe eine Barracuda 7200.12 1 TB, das Laufwerk wird von keinem Betriebssystem erkannt, bevor ich die Platten selbst drehe, macht die Festplatte ein Klickgeräusch, als ob die Köpfe versuchen würden, sich zu bewegen, aber die Platten drehen sich nicht, und dann ertönt ein tiefer Piepton.

Nachdem ich die Festplatte geöffnet hatte, ließ ich sie in Zeitlupe rotieren, dann legte sie los. Von da an kam das seltsame laute Geräusch.

Ich denke einfach, dass der Plattenteller falsch ausgerichtet ist, was ein großes Problem darstellt :) Im Anhang finden Sie ein Video zu diesem Sound.

https://www.youtube.com/watch?v=2K_neijG1rE

Nachdem ich nun die Schrauben so eingestellt habe, wie David vorgeschlagen hat, konnte ich die Festplatte zweimal in meiner Festplattenliste sehen. Unten ist das Dmesg-Protokoll.

[  986.211268] sd 1:0:0:0: Attached scsi generic sg1 type 0
[  986.211651] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[  986.211947] sd 1:0:0:0: [sdb] Write Protect is off
[  986.211952] sd 1:0:0:0: [sdb] Mode Sense: 28 00 00 00
[  986.212325] sd 1:0:0:0: [sdb] No Caching mode page found
[  986.212335] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 1016.704426] usb 1-1: reset high-speed USB device number 8 using xhci_hcd
[ 1049.430537] usb 1-1: reset high-speed USB device number 8 using xhci_hcd
[ 1060.550003] usb 1-1: USB disconnect, device number 8
[ 1060.550028] sd 1:0:0:0: Device offlined - not ready after error recovery
[ 1060.550043] sd 1:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 1060.550048] sd 1:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 1060.550052] blk_update_request: I/O error, dev sdb, sector 0
[ 1060.550061] Buffer I/O error on dev sdb, logical block 0, async page read
[ 1060.550120] sd 1:0:0:0: rejecting I/O to offline device
[ 1060.550143] ldm_validate_partition_table(): Disk read failed.
[ 1060.550176] Dev sdb: unable to read RDB block 0
[ 1060.550226]  sdb: unable to read partition table
[ 1060.550597] sd 1:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 1060.550600] sd 1:0:0:0: [sdb] Sense not available.
[ 1060.550605] sd 1:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 1060.550629] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1911.705428] usb 1-1: new high-speed USB device number 9 using xhci_hcd
[ 1911.846722] usb 1-1: New USB device found, idVendor=152d, idProduct=2338
[ 1911.846727] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1911.846730] usb 1-1: Product: USB to ATA/ATAPI bridge
[ 1911.846732] usb 1-1: Manufacturer: JMicron
[ 1911.846734] usb 1-1: SerialNumber: 000000000000
[ 1911.847857] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 1911.848150] scsi host1: usb-storage 1-1:1.0
[ 1912.878129] scsi 1:0:0:0: Direct-Access     ST310005 28AS                  PQ: 0 ANSI: 5
[ 1912.878875] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 1912.878927] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1912.879139] sd 1:0:0:0: [sdb] Write Protect is off
[ 1912.879142] sd 1:0:0:0: [sdb] Mode Sense: 28 00 00 00
[ 1912.879425] sd 1:0:0:0: [sdb] No Caching mode page found
[ 1912.879431] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 1944.367889] usb 1-1: reset high-speed USB device number 9 using xhci_hcd
[ 1977.122025] usb 1-1: reset high-speed USB device number 9 using xhci_hcd
[ 1988.265153] sd 1:0:0:0: Device offlined - not ready after error recovery
[ 1988.265173] sd 1:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 1988.265180] sd 1:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 1988.265184] blk_update_request: I/O error, dev sdb, sector 0
[ 1988.265188] usb 1-1: USB disconnect, device number 9
[ 1988.265197] Buffer I/O error on dev sdb, logical block 0, async page read
[ 1988.265250] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265274] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265281] ldm_validate_partition_table(): Disk read failed.
[ 1988.265290] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265301] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265312] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265323] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265329] Dev sdb: unable to read RDB block 0
[ 1988.265338] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265349] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265387]  sdb: unable to read partition table
[ 1988.267016] sd 1:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 1988.267022] sd 1:0:0:0: [sdb] Sense not available.
[ 1988.267032] sd 1:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 1988.267075] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 2167.158983] usb 1-1: new high-speed USB device number 10 using xhci_hcd
[ 2167.300232] usb 1-1: New USB device found, idVendor=152d, idProduct=2338
[ 2167.300237] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 2167.300240] usb 1-1: Product: USB to ATA/ATAPI bridge
[ 2167.300242] usb 1-1: Manufacturer: JMicron
[ 2167.300244] usb 1-1: SerialNumber: 000000000000
[ 2167.301229] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2167.301516] scsi host1: usb-storage 1-1:1.0
[ 2168.319867] scsi 1:0:0:0: Direct-Access     ST310005 28AS                  PQ: 0 ANSI: 5
[ 2168.321028] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 2168.321243] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 2168.321571] sd 1:0:0:0: [sdb] Write Protect is off
[ 2168.321577] sd 1:0:0:0: [sdb] Mode Sense: 28 00 00 00
[ 2168.321863] sd 1:0:0:0: [sdb] No Caching mode page found
[ 2168.321875] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 2200.381339] usb 1-1: reset high-speed USB device number 10 using xhci_hcd
[ 2233.107466] usb 1-1: reset high-speed USB device number 10 using xhci_hcd
[ 2244.250856] sd 1:0:0:0: Device offlined - not ready after error recovery
[ 2244.250860] usb 1-1: USB disconnect, device number 10
[ 2244.250875] sd 1:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 2244.250881] sd 1:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 2244.250884] blk_update_request: I/O error, dev sdb, sector 0
[ 2244.250894] Buffer I/O error on dev sdb, logical block 0, async page read
[ 2244.250949] sd 1:0:0:0: rejecting I/O to offline device
[ 2244.250969] sd 1:0:0:0: rejecting I/O to offline device
[ 2244.250975] ldm_validate_partition_table(): Disk read failed.
[ 2244.251008] Dev sdb: unable to read RDB block 0
[ 2244.251059]  sdb: unable to read partition table
[ 2244.251470] sd 1:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 2244.251474] sd 1:0:0:0: [sdb] Sense not available.
[ 2244.251484] sd 1:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 2244.251525] sd 1:0:0:0: [sdb] Attached SCSI disk

unterhalb von lsusb -v

Bus 001 Device 011: ID 152d:2338 JMicron Technology Corp. / JMicron USA Technology Corp. JM20337 Hi-Speed USB to SATA & PATA Combo Bridge
Couldn't open device, some information will be missing

Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x152d JMicron Technology Corp. / JMicron USA Technology Corp.
  idProduct          0x2338 JM20337 Hi-Speed USB to SATA & PATA Combo Bridge
  bcdDevice            1.00
  iManufacturer           1 
  iProduct                2 
  iSerial                 5 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          4 
    bmAttributes         0xc0
      Self Powered
    MaxPower                2mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk-Only
      iInterface              6 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0

Antwort1

Auf Ihrem Video sehe ich, dass die Oberseite des Laufwerks abgenommen ist. Wenn ich meine früheren Kommentare zum Thema Staub außer Acht lasse (zu denen ich immer noch stehe – und tatsächlich wird es noch schlimmer sein, die Platte mit freiliegenden Platten laufen zu lassen), ist der Laufwerksdeckel ein strukturelles Element des Laufwerks und muss mit dem richtigen Drehmoment an den Schrauben befestigt werden –DasEin YouTube-Video zeigt, wie wichtig das richtige Drehmoment ist.

verwandte Informationen