Ich habe einige Probleme mit Ping. Als Root-Benutzer kann ich nicht pingen, wenn ich nicht eingebe, von welcher Schnittstelle aus ich gehen soll. Wenn ich also „google.com pinge“, wird kein Ping ausgeführt. Aber wenn ich pinge wie „ping -I eth0“, wird ein Ping ausgeführt. (OK, es sind keine Routenprobleme, es sind auch andere Parameterprobleme). Ich arbeite also mit MONIT, wo ich ihm gerne sage, dass er den Tunnel neu starten soll, wenn kein Ping ausgeführt wird oder was auch immer. Also ändere ich die Datei /root/.bashrc und füge die Ping-Parameter hinzu, und wenn ich mich bei einer Maschine anmelde, habe ich einen erfolgreichen Ping, ohne die Parameter anzugeben. ABER wenn ich pinge wie „/bin/ping google.com“, wieder dasselbe Problem, es übernimmt die Parameter nicht aus .bashrc. Aber MONIT übernimmt bashrc nicht, sondern führt es einfach aus bin aus (siehe Protokolldateien).
localhost sudo: root : TTY=pts/0 ; PWD=/etc/monit.d ; USER=root ; COMMAND=/bin/ping 192.168.1.1
Auch wenn ich mich mit einem anderen Benutzer anmelde, gibt der Benutzer in derselben Situation überhaupt keinen Ping aus. Wenn ich mich als Root anmelde und den Ping verwende (aber die .bashrc-Parameter für Ping eingebe), funktioniert alles perfekt.
Ich möchte also diesen Standard-Ping mit diesen Parametern ändern, also nicht messen, wie ich ihn ausführe und mit welchem Benutzer er die von mir eingegebenen Parameter verwendet. Gibt es eine Möglichkeit, dies zu tun?
###############################################################################
## Monit control file
###############################################################################
##
## Comments begin with a '#' and extend through the end of the line. Keywords
## are case insensitive. All path's MUST BE FULLY QUALIFIED, starting with '/'.
##
## Below you will find examples of some frequently used statements. For
## information about the control file and a complete list of statements and
## options, please have a look in the Monit manual.
##
##
###############################################################################
## Global section
###############################################################################
##
## Start Monit in the background (run as a daemon):
#
# set daemon 120 # check services at 2-minute intervals
# with start delay 240 # optional: delay the first check by 4-minutes (by
# # default Monit check immediately after Monit start)
#
#
## Set syslog logging with the 'daemon' facility. If the FACILITY option is
## omitted, Monit will use 'user' facility by default. If you want to log to
## a standalone log file instead, specify the full path to the log file
#
# set logfile syslog facility log_daemon
#
#
### Set the location of the Monit id file which stores the unique id for the
### Monit instance. The id is generated and stored on first Monit start. By
### default the file is placed in $HOME/.monit.id.
#
# set idfile /var/.monit.id
#
### Set the location of the Monit state file which saves monitoring states
### on each cycle. By default the file is placed in $HOME/.monit.state. If
### the state file is stored on a persistent filesystem, Monit will recover
### the monitoring state across reboots. If it is on temporary filesystem, the
### state will be lost on reboot which may be convenient in some situations.
#
# set statefile /var/.monit.state
#
## Set the list of mail servers for alert delivery. Multiple servers may be
## specified using a comma separator. By default Monit uses port 25 - it is
## possible to override this with the PORT option.
#
# set mailserver mail.bar.baz, # primary mailserver
# backup.bar.baz port 10025, # backup mailserver on port 10025
# localhost # fallback relay
#
#
## By default Monit will drop alert events if no mail servers are available.
## If you want to keep the alerts for later delivery retry, you can use the
## EVENTQUEUE statement. The base directory where undelivered alerts will be
## stored is specified by the BASEDIR option. You can limit the maximal queue
## size using the SLOTS option (if omitted, the queue is limited by space
## available in the back end filesystem).
#
# set eventqueue
# basedir /var/monit # set the base directory where events will be stored
# slots 100 # optionally limit the queue size
#
#
## Send status and events to M/Monit (for more informations about M/Monit
## see http://mmonit.com/).
#
# set mmonit http://monit:[email protected]:8080/collector
#
#
## Monit by default uses the following alert mail format:
##
## --8<--
## From: monit@$HOST # sender
## Subject: monit alert -- $EVENT $SERVICE # subject
##
## $EVENT Service $SERVICE #
## #
## Date: $DATE #
## Action: $ACTION #
## Host: $HOST # body
## Description: $DESCRIPTION #
## #
## Your faithful employee, #
## Monit #
## --8<--
##
## You can override this message format or parts of it, such as subject
## or sender using the MAIL-FORMAT statement. Macros such as $DATE, etc.
## are expanded at runtime. For example, to override the sender, use:
#
# set mail-format { from: [email protected] }
#
#
## You can set alert recipients whom will receive alerts if/when a
## service defined in this file has errors. Alerts may be restricted on
## events by using a filter as in the second example below.
#
# set alert [email protected] # receive all alerts
# set alert [email protected] only on { timeout } # receive just service-
# # timeout alert
#
#
## Monit has an embedded web server which can be used to view status of
## services monitored and manage services from a web interface. See the
## Monit Wiki if you want to enable SSL for the web server.
#
set httpd port 2812 and
use address x.x.x.x.x # only accept connection from localhost
allow 0.0.0.0/0.0.0.0 # allow localhost to connect to the server and
allow admin:password # require user 'admin' with password 'monit'
allow @monit # allow users of group 'monit' to connect (rw)
allow @users readonly # allow users of group 'users' to connect readonly
#
###############################################################################
## Services
###############################################################################
##
## Check general system resources such as load average, cpu and memory
## usage. Each test specifies a resource, conditions and the action to be
## performed should a test fail.
#
# check system myhost.mydomain.tld
# if loadavg (1min) > 4 then alert
# if loadavg (5min) > 2 then alert
# if memory usage > 75% then alert
# if cpu usage (user) > 70% then alert
# if cpu usage (system) > 30% then alert
# if cpu usage (wait) > 20% then alert
#
#
## Check a file for existence, checksum, permissions, uid and gid. In addition
## to alert recipients in the global section, customized alert can be sent to
## additional recipients by specifying a local alert handler. The service may
## be grouped using the GROUP option. More than one group can be specified by
## repeating the 'group name' statement.
#
# check file apache_bin with path /usr/local/apache/bin/httpd
# if failed checksum and
# expect the sum 8f7f419955cefa0b33a2ba316cba3659 then unmonitor
# if failed permission 755 then unmonitor
# if failed uid root then unmonitor
# if failed gid root then unmonitor
# alert [email protected] on {
# checksum, permission, uid, gid, unmonitor
# } with the mail-format { subject: Alarm! }
# group server
#
#
## Check that a process is running, in this case Apache, and that it respond
## to HTTP and HTTPS requests. Check its resource usage such as cpu and memory,
## and number of children. If the process is not running, Monit will restart
## it by default. In case the service is restarted very often and the
## problem remains, it is possible to disable monitoring using the TIMEOUT
## statement. This service depends on another service (apache_bin) which
## is defined above.
#
# check process apache with pidfile /usr/local/apache/logs/httpd.pid
# start program = "/etc/init.d/httpd start" with timeout 60 seconds
# stop program = "/etc/init.d/httpd stop"
# if cpu > 60% for 2 cycles then alert
# if cpu > 80% for 5 cycles then restart
# if totalmem > 200.0 MB for 5 cycles then restart
# if children > 250 then restart
# if loadavg(5min) greater than 10 for 8 cycles then stop
# if failed host www.tildeslash.com port 80 protocol http
# and request "/somefile.html"
# then restart
# if failed port 443 type tcpssl protocol http
# with timeout 15 seconds
# then restart
# if 3 restarts within 5 cycles then timeout
# depends on apache_bin
# group server
#
#
## Check filesystem permissions, uid, gid, space and inode usage. Other services,
## such as databases, may depend on this resource and an automatically graceful
## stop may be cascaded to them before the filesystem will become full and data
## lost.
#
# check filesystem datafs with path /dev/sdb1
# start program = "/bin/mount /data"
# stop program = "/bin/umount /data"
# if failed permission 660 then unmonitor
# if failed uid root then unmonitor
# if failed gid disk then unmonitor
# if space usage > 80% for 5 times within 15 cycles then alert
# if space usage > 99% then stop
# if inode usage > 30000 then alert
# if inode usage > 99% then stop
# group server
#
#
## Check a file's timestamp. In this example, we test if a file is older
## than 15 minutes and assume something is wrong if its not updated. Also,
## if the file size exceed a given limit, execute a script
#
# check file database with path /data/mydatabase.db
# if failed permission 700 then alert
# if failed uid data then alert
# if failed gid data then alert
# if timestamp > 15 minutes then alert
# if size > 100 MB then exec "/my/cleanup/script" as uid dba and gid dba
#
#
## Check directory permission, uid and gid. An event is triggered if the
## directory does not belong to the user with uid 0 and gid 0. In addition,
## the permissions have to match the octal description of 755 (see chmod(1)).
#
# check directory bin with path /bin
# if failed permission 755 then unmonitor
# if failed uid 0 then unmonitor
# if failed gid 0 then unmonitor
#
#
## Check a remote host availability by issuing a ping test and check the
## content of a response from a web server. Up to three pings are sent and
## connection to a port and an application level network check is performed.
#
# check host myserver with address 192.168.1.1
# if failed icmp type echo count 3 with timeout 3 seconds then alert
# if failed port 3306 protocol mysql with timeout 15 seconds then alert
# if failed url http://user:[email protected]:8080/?querystring
# and content == 'action="j_security_check"'
# then alert
#
#
###############################################################################
## Includes
###############################################################################
##
## It is possible to include additional configuration parts from other files or
## directories.
#
# include /etc/monit.d/*
#
#
# set daemon mode timeout to 1 minute
set daemon 60
# Include all files from /etc/monit.d/
include /etc/monit.d/*
Mit freundlichen Grüße
Antwort1
Sie können einfach einen „neuen“ Ping-Befehl erstellen (z. B. ein Bash-Skript):
(Benennen Sie Ihren eigentlichen Ping-Befehl in ping.back um)
mv /bin/ping /bin/ping.back
(Bearbeiten Sie einen neuen „Ping“-Befehl mit vim/nano/was auch immer)
vim /bin/ping
(fügen Sie dies in die Datei ein und speichern Sie es)
#! /bin/bash
/bin/ping.back -I eth0 $*
(geben Sie der Datei jetzt rwx-rxrx)
chmod 755 /bin/ping
Spielen!
Antwort2
Erstellen Sie einen Befehlsalias in /etc/bashrc(oder vielleicht/etc/profile.d)
alias ping='ping -I eth0'
Antwort3
Sie könnten die ICMP-Pakete mit iptables markieren und die Ausgabeschnittstelle mit iproute2 erzwingen. Das ist zwar nicht so einfach wie Abdóns Lösung, aber es sollte funktionieren.
Tschüss!