Von ifup(8) und ifdown(8) verwendete interfaces(5)-Datei

Von ifup(8) und ifdown(8) verwendete interfaces(5)-Datei

Ich habe einen drahtlosen USB-Dongle Dlink DWA-131 gekauft. Aber ich kann ihn nicht zum Laufen bringen. In der Liste der unterstützten Hardware habe ich gelesen, dass er unter Ubuntu Plug-and-Play ist.

Ich sahVorgehensweise zur Fehlerbehebung bei drahtlosen Gerätenund habe die Protokolle bekommen. Ich habe sie unten in das Protokoll eingefügt. Außerdem sehe ich, dass Dlink in lsusb aufgeführt ist. Aber es wird im Protokoll unten nicht angezeigt. Der integrierte Intel Pro-Chipsatz funktioniert nicht. Deshalb habe ich diesen Dongle gekauft.

Ich konnte das Protokoll nicht einfügen, da ein Fehler auftrat, dass ich 10 Reputationspunkte benötige, um mehr als 2 Links zu posten. Daher habe ich die Links im Protokoll gelöscht.

W: Some index files failed to download. They have been ignored, or old ones used instead.
Reading package lists... Done
Building dependency tree       
Reading state information... Done
E: Unable to locate package hwinfo
  *-network DISABLED      
       description: Wireless interface
       product: PRO/Wireless 3945ABG [Golan] Network Connection
       vendor: Intel Corporation
       physical id: 0
       bus info: pci@0000:10:00.0
       logical name: wlan0
       version: 02
       serial: 00:1f:3c:a0:c6:69
       width: 32 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
       configuration: broadcast=yes driver=iwl3945 driverversion=3.13.0-32-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11abg
       resources: irq:42 memory:f0000000-f0000fff
  *-network
       description: Ethernet interface
       product: 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile
       vendor: Intel Corporation
       physical id: 8
       bus info: pci@0000:02:08.0
       logical name: eth0
       version: 01
       serial: 00:1e:ec:a1:d5:f0
       size: 10Mbit/s
       capacity: 100Mbit/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half latency=64 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10Mbit/s
       resources: irq:20 memory:f0101000-f0101fff ioport:2000(size=64)
0: phy0: Wireless LAN
    Soft blocked: no
    Hard blocked: yes
wlan0     Interface doesn't support scanning : Network is down

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

Von ifup(8) und ifdown(8) verwendete interfaces(5)-Datei

auto lo
iface lo inet loopback
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=14.04
DISTRIB_CODENAME=trusty
DISTRIB_DESCRIPTION="Ubuntu 14.04.1 LTS"
02:08.0 Ethernet controller [0200]: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile [8086:1068] (rev 01)
    Subsystem: Hewlett-Packard Company Device [103c:30d5]
    Kernel driver in use: e100
10:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
    Subsystem: Hewlett-Packard Company Device [103c:135b]
    Kernel driver in use: iwl3945
Bus 001 Device 002: ID 2001:330d D-Link Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
RUNNING         STATE           WIFI-HARDWARE   WIFI       WWAN-HARDWARE   WWAN      
running         disconnected    disabled        disabled   enabled         disabled  

H/W-Pfad Geräteklasse Beschreibung

                            system      HP 520 Notebook PC (FH562AA#UUF)
/0                          bus         30D5
/0/0                        memory      128KiB BIOS
/0/4                        processor   Intel(R) Core(TM) Duo CPU      T2700  @ 2.33GHz
/0/4/5                      memory      64KiB L1 cache
/0/4/6                      memory      2MiB L2 cache
/0/4/0.1                    processor   Logical CPU
/0/4/0.2                    processor   Logical CPU
/0/a                        memory      3GiB System Memory
/0/a/0                      memory      1GiB SODIMM DDR2 Synchronous 667 MHz (1.5 ns)
/0/a/1                      memory      2GiB SODIMM DDR2 Synchronous 667 MHz (1.5 ns)
/0/100                      bridge      Mobile 945GSE Express Memory Controller Hub
/0/100/2                    display     Mobile 945GSE Express Integrated Graphics Controller
/0/100/2.1                  display     Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller
/0/100/1b                   multimedia  NM10/ICH7 Family High Definition Audio Controller
/0/100/1c                   bridge      NM10/ICH7 Family PCI Express Port 1
/0/100/1c.1                 bridge      NM10/ICH7 Family PCI Express Port 2
/0/100/1c.1/0   wlan0       network     PRO/Wireless 3945ABG [Golan] Network Connection
/0/100/1d                   bus         NM10/ICH7 Family USB UHCI Controller #1
/0/100/1d.7                 bus         NM10/ICH7 Family USB2 EHCI Controller
/0/100/1e                   bridge      82801 Mobile PCI Bridge
/0/100/1e/6                 bridge      CB1410 Cardbus Controller
/0/100/1e/8     eth0        network     82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile
/0/100/1f                   bridge      82801GBM (ICH7-M) LPC Interface Bridge
/0/100/1f.2                 storage     82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode]
/0/1            scsi0       storage     
/0/1/0.0.0      /dev/sda    disk        500GB TOSHIBA MQ01ABD0
/0/1/0.0.0/1    /dev/sda1   volume      55GiB Windows NTFS volume
/0/1/0.0.0/2    /dev/sda2   volume      410GiB Extended partition
/0/1/0.0.0/2/5  /dev/sda5   volume      195GiB HPFS/NTFS partition
/0/1/0.0.0/2/6  /dev/sda6   volume      172GiB HPFS/NTFS partition
/0/1/0.0.0/2/7  /dev/sda7   volume      3060MiB Linux swap / Solaris partition
/0/1/0.0.0/2/8  /dev/sda8   volume      39GiB Linux filesystem partition
/0/2            scsi1       storage     
/0/2/0.0.0      /dev/cdrom  disk        DVDRAM GSA-T20N
Linux prasanna 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:12 UTC 2014 i686 i686 i686 GNU/Linux
[    0.000000] DMI: Hewlett-Packard HP 520 Notebook PC/30D5, BIOS 68MVU Ver. F.07 03/18/2008
[    0.000000] Found optimal setting for mtrr clean up
[    0.124777] ACPI: No dock devices found.
[    0.125240] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[    0.125278] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[    0.160686] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.166459] Found 1 acpi root devices
[    0.166601] usbcore: registered new interface driver usbfs
[    0.166601] usbcore: registered new interface driver hub
[    0.166601] usbcore: registered new device driver usb
[    0.170087] Switched to clocksource hpet
[    0.179321] pnp: PnP ACPI: found 11 devices
[    0.218302] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[    0.668099] Console: switching to colour frame buffer device 128x48
[    0.696460] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[    0.696494] ACPI: Lid Switch [C20C]
[    0.808119] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.808122] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.808125] usb usb1: Product: EHCI Host Controller
[    0.808128] usb usb1: Manufacturer: Linux 3.13.0-32-generic ehci_hcd
[    0.808130] usb usb1: SerialNumber: 0000:00:1d.7
[    0.808257] hub 1-0:1.0: USB hub found
[    0.808932] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    0.808935] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.808938] usb usb2: Product: UHCI Host Controller
[    0.808940] usb usb2: Manufacturer: Linux 3.13.0-32-generic uhci_hcd
[    0.808943] usb usb2: SerialNumber: 0000:00:1d.0
[    0.809057] hub 2-0:1.0: USB hub found
[    0.817703] Loaded X.509 cert 'Magrathea: Glacier signing key: a7fc6590fc4a8d859aaebda2ca5dd04716244fa0'
[    0.885012] IMA: No TPM chip found, activating TPM-bypass!
[    0.886064] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.097279] isapnp: No Plug & Play device found
[    1.120094] usb 1-2: new high-speed USB device number 2 using ehci-pci
[    1.261678] usb 1-2: New USB device found, idVendor=2001, idProduct=330d
[    1.261683] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.261686] usb 1-2: Product: 802.11n WLAN Adapter
[    1.261689] usb 1-2: Manufacturer: Realtek
[    1.261691] usb 1-2: SerialNumber: 00e04c000001
[    1.264957] e100 0000:02:08.0 eth0: addr 0xf0101000, irq 20, MAC addr 00:1e:ec:a1:d5:f0
[    9.280791] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    9.595991] [Firmware Bug]: _BCQ is used instead of _BQC
[    9.596042] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[    9.606285] lp: driver loaded but no devices found
[    9.669604] Console: switching to colour dummy device 80x25
[    9.676143] cfg80211: Calling CRDA to update world regulatory domain
[    9.781350] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:s
[    9.781356] iwl3945: Copyright(c) 2003-2011 Intel Corporation
[    9.787063] iwl3945 0000:10:00.0: can't disable ASPM; OS doesn't have ASPM control
[    9.853481] iwl3945 0000:10:00.0: Tunable channels: 11 802.11bg, 13 802.11a channels
[    9.853487] iwl3945 0000:10:00.0: Detected Intel Wireless WiFi Link 3945ABG
[    9.853563] iwl3945 0000:10:00.0: irq 42 for MSI/MSI-X
[    9.863209] yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:30d5]
[    9.877750] ieee80211 phy0: Selected rate control algorithm 'iwl-3945-rs'
[    9.971759] usbcore: registered new interface driver rtl8192cu
[   10.436116] Console: switching to colour frame buffer device 160x50
[   10.440962] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   10.448407] leds_ss4200: no LED devices found
[   10.844713] cfg80211: World regulatory domain updated:
[   10.844720] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.844722] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.844725] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.844727] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.844729] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.844731] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.901287] EXT4-fs (sda8): re-mounted. Opts: errors=remount-ro
[   14.606592] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   14.626272] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   14.627509] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   15.248165] type=1400 audit(1418673050.858:48): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/telepathy/telepathy-ofono" pid=745 comm="apparmor_parser"
[   15.248956] type=1400 audit(1418673050.858:50): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/telepathy/telepathy-ofono" pid=745 comm="apparmor_parser"
[   15.249291] type=1400 audit(1418673050.858:51): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/telepathy/telepathy-ofono" pid=745 comm="apparmor_parser"
    Release Date: 03/18/2008
        Serial services are supported (int 14h)
    Manufacturer: Hewlett-Packard
    Product Name: HP 520 Notebook PC
    Serial Number: CND8374QLD
    Manufacturer: Hewlett-Packard
    Product Name: 30D5
    Serial Number: Not Specified
    Manufacturer: Hewlett-Packard
    Serial Number: CND8374QLD
    Manufacturer: Intel(R)
    Serial Number: Not Specified
    Manufacturer: CE00000000000000
    Serial Number: 303EDB82
    Manufacturer: 7F98000000000000
    Serial Number: 7A15580F
wlan0     IEEE 802.11abg  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=off   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:off

lo        no wireless extensions.

eth0      no wireless extensions.

install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; }
# which ath5k cannot recover. To prevent this condition, stop
blacklist ath_pci
blacklist eth1394
# replaced by p54pci
blacklist prism54
# replaced by b43 and ssb.
blacklist bcm43xx
blacklist acer-wmi
blacklist uart6850
blacklist twl4030_wdt
# /etc/modprobe.d/iwlwifi.conf
# iwlwifi will dyamically load either iwldvm or iwlmvm depending on the
# microcode file installed on the system.  When removing iwlwifi, first
# remove the iwl?vm module and then iwlwifi.
remove iwlwifi \
(/sbin/lsmod | grep -o -e ^iwlmvm -e ^iwldvm -e ^iwlwifi | xargs /sbin/rmmod) \
&& /sbin/modprobe -r mac80211
[main]
NetworkingEnabled=true
WirelessEnabled=true
WWANEnabled=true
WimaxEnabled=true
sudo: hwinfo: command not found
root       669  0.0  0.3  54488 10208 ?        Ssl  01:20   0:00 NetworkManager
prasanna  2277  0.0  0.0   4432   768 pts/2    S+   01:26   0:00 egrep --color=auto wpa|icd|etwork
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
#     DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
total 28428
2097153 drwxr-xr-x  3 root root     4096 Dec  8 06:23 .
      2 drwxr-xr-x 22 root root     4096 Dec  8 06:21 ..
2097156 -rw-r--r--  1 root root  1166929 Jul 15 10:36 abi-3.13.0-32-generic
2097157 -rw-r--r--  1 root root   169732 Jul 15 10:36 config-3.13.0-32-generic
2097154 drwxr-xr-x  5 root root     4096 Dec  8 06:22 grub
2097173 -rw-r--r--  1 root root 18701723 Dec  8 06:23 initrd.img-3.13.0-32-generic
2097158 -rw-r--r--  1 root root   176500 Mar 12  2014 memtest86+.bin
2097159 -rw-r--r--  1 root root   178176 Mar 12  2014 memtest86+.elf
2097160 -rw-r--r--  1 root root   178680 Mar 12  2014 memtest86+_multiboot.bin
2097155 -rw-------  1 root root  2693057 Jul 15 10:36 System.map-3.13.0-32-generic
2109674 -rw-r--r--  1 root root  5820336 Jul 23 03:54 vmlinuz-3.13.0-32-generic
Support status summary of 'prasanna':


You have 1693 packages (100.0%) that can not/no-longer be downloaded
You have 0 packages (0.0%) that are unsupported

Run with --show-unsupported, --show-supported or --show-all to see more details
--2014-12-16 01:26:28--  http://www.linux-usb.org/usb.ids
Resolving www.linux-usb.org (www.linux-usb.org)... failed: Name or service not known.
wget: unable to resolve host address ‘www.linux-usb.org’
update-usbids: download failed
Module                  Size  Used by
bnep                   18895  2 
rfcomm                 53664  0 
bluetooth             342206  10 bnep,rfcomm
snd_hda_codec_conexant    47785  1 
hp_wmi                 13702  0 
sparse_keymap          13708  1 hp_wmi
pcmcia                 51828  0 
parport_pc             31981  0 
coretemp               13195  0 
ppdev                  17391  0 
rtl8192cu              66675  0 
kvm                   388083  0 
snd_hda_intel          42730  2 
snd_hda_codec         164067  2 snd_hda_codec_conexant,snd_hda_intel
snd_hwdep              13272  1 snd_hda_codec
snd_pcm                85501  2 snd_hda_codec,snd_hda_intel
joydev                 17101  0 
arc4                   12536  2 
yenta_socket           40201  0 
pcmcia_rsrc            18319  1 yenta_socket
rtl_usb                18072  1 rtl8192cu
serio_raw              13230  0 
lpc_ich                16864  0 
pcmcia_core            22328  3 pcmcia,pcmcia_rsrc,yenta_socket
iwl3945                63619  0 
iwlegacy               88016  1 iwl3945
rtlwifi                52835  2 rtl_usb,rtl8192cu
snd_page_alloc         14230  2 snd_pcm,snd_hda_intel
rtl8192c_common        47340  1 rtl8192cu
snd_seq_midi           13132  0 
mac80211              546051  5 iwl3945,iwlegacy,rtl_usb,rtlwifi,rtl8192cu
snd_seq_midi_event     14475  1 snd_seq_midi
snd_rawmidi            25135  1 snd_seq_midi
snd_seq                55383  2 snd_seq_midi_event,snd_seq_midi
snd_seq_device         14137  3 snd_seq,snd_rawmidi,snd_seq_midi
snd_timer              28584  2 snd_pcm,snd_seq
cfg80211              409394  4 iwl3945,iwlegacy,mac80211,rtlwifi
i915                  705659  3 
wmi                    18673  1 hp_wmi
drm_kms_helper         47182  1 i915
snd                    60871  14 snd_hwdep,snd_timer,snd_hda_codec_conexant,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi
video                  18903  1 i915
lp                     13299  0 
parport                40836  3 lp,ppdev,parport_pc
mac_hid                13037  0 
drm                   244037  4 i915,drm_kms_helper
i2c_algo_bit           13197  1 i915
soundcore              12600  1 snd
psmouse                91329  0 
e100                   35945  0 
mii                    13654  1 e100

danke an alle

Antwort1

Sie können dies lesenArtikelund versuche:

sudo modprobe rtl8192cu swenc=1
echo "2001 330D" | sudo tee /sys/bus/usb/drivers/rtl8192cu/new_id 

Antwort2

Mein D-Link-WLAN-Dongle hat die folgenden Spezifikationen:

  • D-Link Wireless N300 Nano USB-Adapter
  • Modellnummer: DWA-131
  • H/W-Version: E1
  • F/W-Version: 5.00

Folgendes habe ich getan, nachdem ich sehr lange im Internet gesucht hatte:

1) Gehe zuhttp://support.dlink.com.au/Download/download.aspx?product=DWA-131und laden Sie die Datei „DWA-131 Linux driver v4.3.1.1.zip (5,88 MB)“ im Abschnitt „REV E“ (oben auf der Seite) herunter. 2) Verschieben Sie die Datei in ein Verzeichnis Ihrer Wahl, entpacken Sie sie und wechseln Sie in das Verzeichnis, das Sie gerade entpackt haben. Dies ist (im von Ihnen gewählten Verzeichnis):

  • tar -zxvf 20140812_rtl8192EU_linux_v4.3.1.1_11320.tar.gz
  • cd 20140812_rtl8192EU_linux_v4.3.1.1_11320/

3) Geben Sie die folgenden Befehle ein:

  • machen
  • su (Ihr Passwort wird benötigt)
  • machen installieren

Sie müssen Ihren Computer nicht einmal neu starten. In meinem Fall hat es sofort funktioniert.

Ich hoffe, Sie finden diese Informationen nützlich.

Antwort3

http://h18000.www1.hp.com/products/quickspecs/archives_Division/12721_div_v1/12721_div.HTML

HP 520 Notebook

Haben Sie versucht, den Knopf links neben dem Einschaltknopf zu drücken, um zu sehen, ob er WLAN aktiviert? Er ist Nr. 2 auf dem Bild. Wenn er wie vorgesehen funktioniert, sollte er zumindest den Hardblock inrfkill list all

verwandte Informationen