☰

Controlador inalámbrico no detectado

tag-icon • tag-icon 11.04 networking wireless
Controlador inalámbrico no detectado

Al escribir iwconfig solo aparece "sin extensiones inalámbricas"

¿Cómo consigo que se detecte el controlador inalámbrico de Ubuntu?

lspci:

00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
00:04.0 PCI bridge: ATI Technologies Inc Device 7914
00:05.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 1)
00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2)
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2)
00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series]
02:04.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b6)
02:04.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 02)
10:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02)

lsusb:

Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 08ff:2580 AuthenTec, Inc. AES2501 Fingerprint Sensor
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 004: ID 066f:8000 SigmaTel, Inc. MSCN MP3 Player
Bus 002 Device 002: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface [Integrated Module]
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

sudo lshw -class network:

 *-network
       description: Ethernet interface
       product: NetLink BCM5787M Gigabit Ethernet PCI Express
       vendor: Broadcom Corporation
       physical id: 0
       bus info: pci@0000:10:00.0
       logical name: eth0
       version: 02
       serial: 00:1a:4b:82:59:ee
       capacity: 1Gbit/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.116 firmware=sb v2.09 latency=0 link=no multicast=yes port=twisted pair
       resources: irq:43 memory:d0000000-d000ffff

/etc/red/interfaces:

auto lo
iface lo inet loopback

sudo rfkill list:

0: hci0: Bluetooth
      Soft blocked: no
      Hard blocked: no
1: hp-wifi: Wireless LAN
      Soft blocked: yes
      Hard blocked: no
2: hp-bluetooth: Bluetooth
      Soft blocked: no
      Hard blocked: no

Respuesta1

El resultado sudo rfkill listmuestra que su tarjeta de red está "bloqueada suavemente".

Esto podría suceder cuando se ha indicado a la tarjeta inalámbrica que se apague; probablemente se deba a un interruptor de tipo Fn+.

Si no identifica el interruptor del teclado, realice los siguientes pasos:

  1. ejecutar en una terminal:

    sudo rfkill unblock hp-wifi; sudo rfkill unblock wifi; sudo rfkill unblock all

  2. Vuelva a ejecutar sudo rfkill listpara confirmar que la tarjeta ha sido desbloqueada.

  3. reiniciar

  4. Vuelva a ejecutarlo sudo rfkill listpara confirmar que el desbloqueo se ha conservado.

  5. Vuelva a ejecutar sudo lshw -class network: ahora debería ver que el kernel ha reconocido (o no) la tarjeta inalámbrica.

Si el módulo del kernel inalámbrico ha sido reconocido (no debería decir "no reclamado"), Network Manager ahora debería poder ver las redes inalámbricas que están disponibles en sus alrededores.

información relacionada