USB 3.0 이더넷 네트워크 어댑터(항목 코드 20256, 정확한 모델은 다음과 같습니다)를 구입했습니다.http://www.ugreen.com.cn/product-697-en.html) 그러나 Dell XPS 13 Developer Edition의 Ubuntu 16.04에서는 작동하지 않습니다. 나는 여기를 보았다Ubuntu 16.04가 설치된 Dell XPS 13의 USB-이더넷그러나 성공하지 못했습니다.
USB 어댑터를 삽입하면 처음에는 "이제 '유선 연결 1'에 연결되었습니다."라는 성공 팝업 메시지가 표시되지만 곧 "이더넷 네트워크 연결이 끊어졌습니다."라는 메시지가 나타납니다.
Linux 드라이버 설치를 시도했습니다.http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=131;71;112
그러나 make명령은 다음과 같이 실패합니다.
make -C /lib/modules/4.4.0-78-generic/build SUBDIRS=/home/vito/dev/ethernet ugreen adapter/AX88179_178A_LINUX_DRIVER_v1.18.0_SOURCE modules
make[1]: Entering directory '/usr/src/linux-headers-4.4.0-78-generic'
arch/x86/Makefile:148: CONFIG_X86_X32 enabled but no binutils support
Makefile:693: Cannot use CONFIG_CC_STACKPROTECTOR_STRONG: -fstack-protector-strong not supported by compiler
make[1]: *** No rule to make target 'ugreen'. Stop.
make[1]: Leaving directory '/usr/src/linux-headers-4.4.0-78-generic'
Makefile:30: recipe for target 'default' failed
make: *** [default] Error 2
그리고 달리는 중
sudo add-apt-repository ppa:qji/ax88179
sudo apt-get update
sudo apt-get install ax88179
에 설명된 대로USB 3.0 AX88179 기가비트 이더넷 어댑터를 설치(또는 문제 해결)하는 방법은 무엇입니까?
수확량
E: Unable to locate package ax88179
내 lsusb결과는 다음과 같습니다.
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 0c45:670c Microdia
Bus 001 Device 002: ID 8087:0a2b Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
출력 의 일부 dmesg:
[141344.691045] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[141344.718791] usb 2-1: New USB device found, idVendor=0b95, idProduct=1790
[141344.718794] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[141344.718796] usb 2-1: Product: AX88179
[141344.718797] usb 2-1: Manufacturer: ASIX Elec. Corp.
[141344.718798] usb 2-1: SerialNumber: 00000000000062
[141346.086230] ax88179_178a 2-1:1.0 eth0: register 'ax88179_178a' at usb-0000:00:14.0-1, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:0e:c6:c2:13:fb
[141346.087635] usbcore: registered new interface driver ax88179_178a
[141346.095391] ax88179_178a 2-1:1.0 enx000ec6c213fb: renamed from eth0
[141346.127776] IPv6: ADDRCONF(NETDEV_UP): enx000ec6c213fb: link is not ready
[141346.453080] IPv6: ADDRCONF(NETDEV_UP): enx000ec6c213fb: link is not ready
[141348.334700] ax88179_178a 2-1:1.0 enx000ec6c213fb: ax88179 - Link status is: 1
[141348.341174] IPv6: ADDRCONF(NETDEV_CHANGE): enx000ec6c213fb: link becomes ready
[141353.879023] usb 2-1: USB disconnect, device number 2
[141353.879307] ax88179_178a 2-1:1.0 enx000ec6c213fb: unregister 'ax88179_178a' usb-0000:00:14.0-1, ASIX AX88179 USB 3.0 Gigabit Ethernet
[141353.879336] ax88179_178a 2-1:1.0 enx000ec6c213fb: Failed to read reg index 0x0002: -19
[141353.879342] ax88179_178a 2-1:1.0 enx000ec6c213fb: Failed to write reg index 0x0002: -19
[141353.906952] ax88179_178a 2-1:1.0 enx000ec6c213fb (unregistered): Failed to write reg index 0x0002: -19
[141353.906962] ax88179_178a 2-1:1.0 enx000ec6c213fb (unregistered): Failed to write reg index 0x0001: -19
[141353.906968] ax88179_178a 2-1:1.0 enx000ec6c213fb (unregistered): Failed to write reg index 0x0002: -19
[141354.150699] usb 2-1: Device not responding to setup address.
[141354.354505] usb 2-1: Device not responding to setup address.
[141354.554938] usb 2-1: device not accepting address 3, error -71
[141354.554962] xhci_hcd 0000:00:14.0: Cannot set link state.
[141354.554980] usb usb2-port1: cannot disable (err = -32)
[141354.723064] usb 2-1: new SuperSpeed USB device number 4 using xhci_hcd
[141354.745922] usb 2-1: New USB device found, idVendor=0b95, idProduct=1790
[141354.745930] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[141354.745935] usb 2-1: Product: AX88179
[141354.745939] usb 2-1: Manufacturer: ASIX Elec. Corp.
[141354.745942] usb 2-1: SerialNumber: 00000000000062
[141355.068628] ax88179_178a 2-1:1.0 eth0: register 'ax88179_178a' at usb-0000:00:14.0-1, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:0e:c6:c2:13:fb
[141356.085896] ax88179_178a 2-1:1.0 enx000ec6c213fb: renamed from eth0
[141359.573244] IPv6: ADDRCONF(NETDEV_UP): enx000ec6c213fb: link is not ready
[141359.892335] IPv6: ADDRCONF(NETDEV_UP): enx000ec6c213fb: link is not ready
[141359.982994] ax88179_178a 2-1:1.0 enx000ec6c213fb: ax88179 - Link status is: 1
[141361.775038] ax88179_178a 2-1:1.0 enx000ec6c213fb: ax88179 - Link status is: 1
[141361.782150] IPv6: ADDRCONF(NETDEV_CHANGE): enx000ec6c213fb: link becomes ready
[141377.563329] usb 2-1: USB disconnect, device number 4
[141377.563637] ax88179_178a 2-1:1.0 enx000ec6c213fb: unregister 'ax88179_178a' usb-0000:00:14.0-1, ASIX AX88179 USB 3.0 Gigabit Ethernet
[141377.563670] ax88179_178a 2-1:1.0 enx000ec6c213fb: Failed to read reg index 0x0002: -19
[141377.563676] ax88179_178a 2-1:1.0 enx000ec6c213fb: Failed to write reg index 0x0002: -19
[141377.603221] ax88179_178a 2-1:1.0 enx000ec6c213fb (unregistered): Failed to write reg index 0x0002: -19
[141377.603225] ax88179_178a 2-1:1.0 enx000ec6c213fb (unregistered): Failed to write reg index 0x0001: -19
[141377.603228] ax88179_178a 2-1:1.0 enx000ec6c213fb (unregistered): Failed to write reg index 0x0002: -19
[141399.516121] wlp58s0: deauthenticating from 02:1a:11:fd:4d:c2 by local choice (Reason: 3=DEAUTH_LEAVING)
[141516.771923] usb 1-2: USB disconnect, device number 11
ifconfig산출:
docker0 Link encap:Ethernet HWaddr 02:42:9d:b9:7e:94
inet addr:172.17.0.1 Bcast:0.0.0.0 Mask:255.255.0.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
enx000ec6c213fb Link encap:Ethernet HWaddr 00:0e:c6:c2:13:fb
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:1191 errors:0 dropped:0 overruns:0 frame:0
TX packets:1191 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:145957 (145.9 KB) TX bytes:145957 (145.9 KB)
wlp58s0 Link encap:Ethernet HWaddr e4:a4:71:1c:6c:09
inet addr:192.168.43.103 Bcast:192.168.43.255 Mask:255.255.255.0
inet6 addr: fe80::d7ed:8502:d581:869/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:46483 errors:0 dropped:0 overruns:0 frame:0
TX packets:20201 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:56977580 (56.9 MB) TX bytes:2929160 (2.9 MB)
답변1
나는 Ubuntu 20.04 및 "0b95:1790 ASIX AX88179 10/100/1000"과 같은 상황에 있었습니다. nm-connection-editor(Network Manager)를 살펴보면 둘 이상의 "케이블 연결"을 볼 수 있습니다. 이전글 다 삭제했어요"USB 케이블 연결"USB 동글 이더넷을 분리했다가 다시 연결하면 문제가 해결됩니다.
따라서 이 경험을 통해 문제가 커널 드라이버가 아닌 Network Manager에서 발생했음을 이해할 수 있습니다.