저는 CentOS 7을 사용하고 있습니다.D-link DWA-131 무선-N USB 나노하드웨어 개정E1 어댑터. 드라이버를 다운로드하여 컴파일했습니다.ftp://files.dlink.com.au/products/DWA-131/REV_E/Drivers/DWA-131_Linux_driver_v4.3.1.1.zip. 모듈을 설치하고 삽입한 후8192eu.ko내 장치는 다음과 같이 감지됩니다.USB 이더넷. 무선 네트워크에 연결할 수 있도록 무선 장치로 인식하려면 어떻게 해야 합니까?알파벳비밀번호가 있는12345678.
에 의한 결과uname -a~이다
Linux linux-centos 3.10.0-693.5.2.el7.x86_64 #1 SMP Fri Oct 20 20:32:50 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux
에 의한 결과ifconfig -a~이다
enp0s20u3: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 54:2a:a2:47:dd:f6 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Local Loopback)
RX packets 7729 bytes 664831 (649.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 7729 bytes 664831 (649.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
p4p2: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether f8:ca:b8:06:55:c0 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:1c:39:9e txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0-nic: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:1c:39:9e txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlp6s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.22 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::374e:5cb2:ec50:9c4d prefixlen 64 scopeid 0x20<link>
ether 78:0c:b8:36:8e:31 txqueuelen 1000 (Ethernet)
RX packets 122333 bytes 155288565 (148.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 84226 bytes 10510089 (10.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
enp0s20u3내 USB 장치입니다. 로딩할때만 뜨네요8192eu.ko사용하여모드프로브또는인스모드.
Wi-Fi로 표시된 장치는 '내부 Wi-Fi'이지만 USB 장치는 USB 이더넷으로 감지됩니다.
답변1
나에게는 모듈을 다시 로드한 직후에만 작동합니다.
modprobe -r rtl8xxxu; sleep 2; modprobe rtl8xxxu
(사전 구성된 NetworkManager의 연결)
게다가 추가 옵션도 있습니다:
cat /etc/modprobe.d/rtl8xxxu.conf
options rtl8xxxu ht40_2g=1 dma_aggregation=1 rtw_power_mgnt=0 rtw_enusbss=0