iwd 독립 실행형을 사용하여 인터넷에 연결할 수 없습니다

2024-6-11 • tag-icon

다음을 사용하여 Wi-Fi에 연결하려고 합니다.iwd 독립형, 없이 NetworkManager또는 wpa_supplicant.

netinst이것은 설치가 있고 데스크탑 환경이 없는 Debian 10 시스템에 있습니다 . 에 무료가 아닌 구성 요소를 추가 apt-sources하고 설치했습니다 firmware-iwlwifi.

나는 /etc/iwd/main.conf다음과 같이 수정했다

[General]
EnableNetworkConfiguration=true

[Network]
NameResolvingService=systemd

나는 iwctl연결하곤 했다:

[iwd]# station list
                            Devices in Station Mode                           *
--------------------------------------------------------------------------------
  Name                State          Scanning
--------------------------------------------------------------------------------
  wlp2s0              connected

[iwd]# device list
                                    Devices
--------------------------------------------------------------------------------
  Name                Address             Powered   Adapter   Mode
--------------------------------------------------------------------------------
  wlp2s0              xx:xx:xx:xx:xx:xx   on        phy0      station

실행 중인 서비스는 다음과 같습니다.

UNIT                      LOAD   ACTIVE SUB     DESCRIPTION
cron.service              loaded active running Regular background program processing daemon
dbus.service              loaded active running D-Bus System Message Bus
[email protected]        loaded active running Getty on tty1
iwd.service               loaded active running Wireless service
rsyslog.service           loaded active running System Logging Service
ssh.service               loaded active running OpenBSD Secure Shell server
systemd-journald.service  loaded active running Journal Service
systemd-logind.service    loaded active running Login Service
systemd-networkd.service  loaded active running Network Service
systemd-resolved.service  loaded active running Network Name Resolution
systemd-timesyncd.service loaded active running Network Time Synchronization
systemd-udevd.service     loaded active running udev Kernel Device Manager
[email protected]            loaded active running User Manager for UID 0

LOAD   = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB    = The low-level unit activation state, values depend on unit type.

13 loaded units listed. Pass --all to see loaded but inactive units, too.
To show all installed unit files use 'systemctl list-unit-files'.

드라이버가 로드되었습니다:

lspci | grep -i intel
02:00.0 Network controller: Intel Corporation Wireless-AC 9260 (rev 29)

여기에는 오류가 없습니다.

[    4.807336] iwlwifi 0000:02:00.0 wlp2s0: renamed from wlan0
[    5.330505] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[    9.815999] wlp2s0: authenticate with xx:xx:xx:xx:xx:xx
[    9.825148] wlp2s0: send auth to xx:xx:xx:xx:xx:xx (try 1/3)
[    9.868608] wlp2s0: authenticated
[    9.870031] wlp2s0: associate with xx:xx:xx:xx:xx:xx (try 1/3)
[    9.874042] wlp2s0: RX AssocResp from xx:xx:xx:xx:xx:xx (capab=0x1011 status=0 aid=2)
[    9.877212] wlp2s0: associated
[    9.976363] wlp2s0: Limiting TX power to 23 (23 - 0) dBm as advertised by xx:xx:xx:xx:xx:xx
[   11.900982] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready

하지만 주소/호스트 이름을 핑할 수 없습니다.

이것은 과 관련이 있습니까 dhcpcd?

어떤 아이디어가 있나요?

답변1

Bullseye로 업그레이드하면 문제가 해결됩니다.

답변1

관련 정보