Estou configurando um Cisco ASA 5505 com a licença básica.
A comunicação TCP/UDP funciona de dentro->fora, fora->dentro, dentro->seguro, que é a segurança de tráfego desejada.
HTTP, SSH e outros acessos internos-> seguros funcionam, mas não consigo executar ping de dentro-> seguros (host 192.168.110.0 para host 192.168.7.1 ou 192.168.7.0).
Como posso ativar o ICMP?
Configuração:
interface Vlan1
nameif inside
security-level 100
ip address 192.168.110.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group birdie
ip address removedIP 255.255.255.255 pppoe
!
interface Vlan3
no forward interface Vlan1
nameif secure
security-level 50
ip address 192.168.7.1 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
switchport access vlan 3
!
interface Ethernet0/5
shutdown
!
interface Ethernet0/6
shutdown
!
interface Ethernet0/7
shutdown
!
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
access-list Outside-In extended permit icmp any any
access-list Outside-In extended permit tcp any any eq www
access-list Outside-In extended permit tcp any any eq https
access-list Outside-In extended permit tcp any any eq 5969
access-list inside_nat0_outbound extended permit ip any 192.168.111.0 255.255.255.224
access-list standardUser_splitTunnelAcl1 extended permit ip 192.168.111.0 255.255.255.0 any
access-list standardUser_splitTunnelAcl1 extended permit ip 192.168.110.0 255.255.255.0 any
access-list inside_in extended permit icmp any any
access-list inside_in extended permit ip any any
access-list secure_in extended permit icmp any any
access-list secure_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1492
mtu outside 1492
mtu secure 1500
ip local pool vpnuser 192.168.111.5-192.168.111.20
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (secure) 1 192.168.7.0 255.255.255.0
static (inside,outside) tcp interface https 192.168.110.6 https netmask 255.255.255.255
static (inside,outside) tcp interface www 192.168.110.6 www netmask 255.255.255.255
static (inside,outside) tcp interface 5969 192.168.110.12 5969 netmask 255.255.255.255
static (inside,secure) 192.168.110.0 192.168.110.0 netmask 255.255.255.0
access-group inside_in in interface inside
access-group Outside-In in interface outside
access-group secure_in in interface secure
route outside 0.0.0.0 0.0.0.0 RemovedIP 1
Responder1
A única coisa que me parece estranha na sua configuração é a static(inside,secure)declaração. Parece não funcionar, pois os endereços mapeados e reais são os mesmos. Na minha configuração, também tenho uma rede do tipo dmz e nenhuma static(inside,dmz)instrução. (Eu tenho static(dmz,outside) ...para serviços expostos externamente).
De qualquer forma, tente remover essa estática e veja o efeito que isso tem.