我有一個舊的 Iomega Zip100 驅動器（標記為 ATAPI），我試圖透過 USB-ATA/SATA 橋接器存取它。在Windows 7下，插入會在裝置管理員中出現錯誤（USB大容量儲存裝置：此裝置無法啟動）；在 Linux（Ubuntu 或 Parted Magic）下，我收到dmesg以下訊息：
[ 79.600104] usb 1-1: new high speed USB device number 2 using ehci_hcd
[ 80.276845] usbcore: registered new interface driver uas
[ 80.279191] Initializing USB Mass Storage driver...
[ 80.279319] scsi5 : usb-storage 1-1:1.0
[ 80.279489] usbcore: registered new interface driver usb-storage
[ 80.279490] USB Mass Storage support registered.
[ 104.300076] usb 1-1: reset high speed USB device number 2 using ehci_hcd
[ 106.816100] usb 1-1: device descriptor read/64, error -32
[ 109.400083] usb 1-1: device descriptor read/64, error -32
[ 111.972077] usb 1-1: reset high speed USB device number 2 using ehci_hcd
[ 114.416080] usb 1-1: device descriptor read/64, error -32
[ 116.988076] usb 1-1: device descriptor read/64, error -32
[ 119.525052] usb 1-1: reset high speed USB device number 2 using ehci_hcd
[ 119.605160] usb 1-1: device descriptor read/8, error -32
[ 119.749098] usb 1-1: device descriptor read/8, error -32
[ 122.328071] usb 1-1: reset high speed USB device number 2 using ehci_hcd
[ 122.386670] usb 1-1: device descriptor read/8, error -32
[ 122.531119] usb 1-1: device descriptor read/8, error -32
[ 122.632090] usb 1-1: USB disconnect, device number 2
[ 122.632124] scsi 5:0:0:0: Device offlined - not ready after error recovery
[ 125.204064] usb 1-1: new high speed USB device number 3 using ehci_hcd
[ 129.652662] usb 1-1: device descriptor read/64, error -32
[ 132.708186] usb 1-1: device descriptor read/64, error -32
[ 135.244085] usb 1-1: new high speed USB device number 4 using ehci_hcd
[ 137.732086] usb 1-1: device descriptor read/64, error -32
[ 140.280137] usb 1-1: device descriptor read/64, error -32
[ 142.812108] usb 1-1: new high speed USB device number 5 using ehci_hcd
[ 142.897135] usb 1-1: device descriptor read/8, error -32
[ 143.041068] usb 1-1: device descriptor read/8, error -32
[ 145.564480] usb 1-1: new high speed USB device number 6 using ehci_hcd
[ 145.625696] usb 1-1: device descriptor read/8, error -32
[ 145.770217] usb 1-1: device descriptor read/8, error -32
[ 145.872236] hub 1-0:1.0: unable to enumerate USB device on port 1
我已經嘗試了驅動器上跳線設定的幾種組合（主、電纜選擇/驅動器 A、非驅動器 A）；是否可以透過這樣的 USB 橋接器存取 ZIP 驅動器，或者我是否需要將其插入主機板上的「正確」IDE 通道？
答案1
對於 USB/ATAPI，您必須希望 ATAPI 部分能夠協商良好的傳輸模式，因為您無法控制它。管道損壞意味著設備已斷開連接，這可能意味著 DMA 模式錯誤或電纜不合格 (e)SATA-IDE 轉換器即使不是更好，也應該採取不同的措施。