在 TIKZ 中繪製標記邊且無交點的有向圖

Question

我正在繪製一個有向圖來表示一個矩陣。

\begin{figure}
\begin{tikzpicture}[roundnode/.style={circle, draw=black!60, fill=black!5, very thick, minimum size=7mm}]
%Nodes
\node[roundnode]      (midcircle)                              {2};
\node[roundnode]      (uppercircle)       [above=of midcircle] {1};
\node[roundnode]      (rightcircle)       [right=of midcircle] {4};
\node[roundnode]      (lowercircle)       [below=of midcircle] {3};

%Edges out of 1
\draw[->] (uppercircle.east) -- (rightcircle.north);
\draw[->] (uppercircle.west) .. controls+(left:40mm) .. (lowercircle.west);
\draw[->] (uppercircle.west) .. controls +(up:20mm) and +(right:7mm) .. (uppercircle.east);

%2 Edges out of 2
\draw[->] (midcircle.east) -- (rightcircle.west);
\draw[->] (midcircle.north) .. controls +(up:5mm) and +(right:7mm) .. (midcircle.east);
\draw[->] (midcircle.south) -- (lowercircle.north);
\draw[->] (midcircle.north) -- (uppercircle.south);

%Edges out of 3
\draw[->] (lowercircle.west) .. controls+(left:50mm) and +(up:10mm) .. (uppercircle.west);
\draw[->] (lowercircle.east) -- (rightcircle.south);
\draw[->] (lowercircle.south) .. controls +(right:7mm) ..  (lowercircle.east);


%Edges out of 4
\draw[->] (rightcircle.south) .. controls +(down:7mm) and +(right:7mm) .. (midcircle.east);

\end{tikzpicture}
\end{figure}

這會產生

1. 我想知道如何用簡單的 + 或 - 標記邊緣
2. 我想製作更漂亮的邊緣，不相交，並且更對稱。我不確定使用controls命令是否是最好的方法。讓邊離開和進入而不是在north、south、east或上也可能效果更好west。有更好的方法建議嗎？

Answer 1

這是用函式庫繪製的自動機automata。我用字母標記了所有邊，以便更容易在代碼中識別它們，但當然您也可以使用類似node{\texttt{+}}或 的東西node{$+$}。

\documentclass[border=2mm]{standalone}
\usepackage{tikz}
\usetikzlibrary{automata,positioning}
\begin{document}
\begin{tikzpicture}%
  [>=stealth,
   shorten >=1pt,
   node distance=2cm,
   on grid,
   auto,
   every state/.style={draw=black!60, fill=black!5, very thick}
  ]
\node[state] (mid)                  {2};
\node[state] (upper) [above=of mid] {1};
\node[state] (right) [right=of mid] {4};
\node[state] (lower) [below=of mid] {3};

\path[->]
%   FROM       BEND/LOOP           POSITION OF LABEL   LABEL   TO
   (upper) edge[bend left]     node                      {a} (right)
           edge[bend right=80] node[swap,very near start]{b} (lower)
           edge[loop above]    node                      {c} (upper)
   (mid)   edge[bend left=10]  node                      {d} (right)
           edge[loop left]     node                      {e} (mid)
           edge                node                      {f} (lower)
           edge                node                      {g} (upper)
   (lower) edge[bend left=70]  node[swap,very near start]{h} (upper)
           edge[bend right]    node[swap]                {i} (right)
           edge[loop below]    node                      {j} (lower)
   (right) edge[bend left=10]  node                      {k} (mid)
   ;
\end{tikzpicture}
\end{document}

Answer 2

我不知道我是否完全理解你的問題，但這是一個解決方案。當然不是最好的。

\documentclass{article}
\usepackage{tikz}
\usetikzlibrary{automata,arrows,calc,positioning}

\begin{document}

\begin{figure}
\begin{tikzpicture}[roundnode/.style={circle, draw=black!60, fill=black!5, very thick, minimum size=7mm}]
%Nodes
\node[roundnode]      (midcircle)                              {2};
\node[roundnode]      (uppercircle)       [above=of midcircle] {1};
\node[roundnode]      (rightcircle)       [right=of midcircle] {4};
\node[roundnode]      (lowercircle)       [below=of midcircle] {3};

%Edges out of 1
\draw[->] (uppercircle.east) to[bend left=20] node[above right]{-}(rightcircle.north);
\draw[->] (uppercircle.-135) to[bend right=40] node[right]{-}(lowercircle.135);
\draw[->] (uppercircle.135) to[out=135,in=180] ($(uppercircle) +(0,3em)$)node[above]{+} to[out=0, in =45] (uppercircle.45);

%2 Edges out of 2
\draw[->] (midcircle.east) --node[above]{+} (rightcircle.west);
\draw[->] (midcircle.80) to[out=80,in=135] ($(midcircle) +(2em,2em)$)node[right]{+}  to[out=-45, in =10] (midcircle.10);
\draw[->] (midcircle.south) -- (lowercircle.north);
\draw[->] (midcircle.north) -- (uppercircle.south);

%Edges out of 3
\draw[->] (lowercircle.150) to[bend left=80]node[left]{+}(uppercircle.-150);
\draw[->] (lowercircle.east) to[bend right=20]node[below right]{-}(rightcircle.south);
\draw[->] (lowercircle.-135)  to[out=-135,in=180] ($(lowercircle) +(0,-3em)$)node[below]{+} to[out=0, in =-45](lowercircle.-45);


%Edges out of 4
\draw[->] (rightcircle.-135) to[bend left=20] node[below]{-} (midcircle.-45);

\end{tikzpicture}
\end{figure}

\end{document}